Home
JAQForum Ver 20.06
Log In or Join  
Active Topics
Local Time 19:04 20 Apr 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Solar : Solar lamp

Author Message
vasi

Guru

Joined: 23/03/2007
Location: Romania
Posts: 1697
Posted: 12:25pm 22 Jan 2008
Copy link to clipboard 
Print this post

I received 4 solar lamps as christmas gift.





The solar cell charging one AAA NiCd accu 1.2V, 600mAh.

The question is, how powerful this cell is? Anyone know? Edited by vasi 2008-01-23
Hobbit name: Togo Toadfoot of Frogmorton
Elvish name: Mablung Miriel
Beyound Arduino Lang
 
wind-pirate

Senior Member

Joined: 01/02/2007
Location: Canada
Posts: 101
Posted: 01:24am 25 Jan 2008
Copy link to clipboard 
Print this post

We have about 25 lights. some have two batteries in then. I have seen 3.5 volts out of some of them.
"In the bright sun" some are about 5 years old now. The batteries don't hold a charge as good as they once did. Keep them clean "the contacts" so they will charge. They need at least 5 hours sun a day.

Ron
THE Pirate.
stealing wind & solar energy is fun
 
Tinker

Guru

Joined: 07/11/2007
Location: Australia
Posts: 1904
Posted: 12:05pm 25 Jan 2008
Copy link to clipboard 
Print this post

Vasi, it is easy to find that out yourself. I assume you have a multi meter? If so, set it to read current (200mA range) and short circuit the solar cell with the ampmeter. If you do that with the cell facing the sun you will see the maximum short circuit current the cell can produce. Don't worry about the short, all solar cells can handle a short circuit easily - as long as your meter can handle the current.
Now, set the meter to read DC volts, 10V range, and measure the output volts at the cell with no load.
You now have two maximum figures, both DO depent on the solar strength which is not a lot in your winter I assume.
The useful output of your cell is somewhat less than the short circuit current you measured.
Klaus
Klaus
 
vasi

Guru

Joined: 23/03/2007
Location: Romania
Posts: 1697
Posted: 05:34pm 25 Jan 2008
Copy link to clipboard 
Print this post

Thank you guys,

I wanted to not destroy that cell soldering wires if don't work... better using them as solar lamps.

But I can destroy one, I must know the results.
Hobbit name: Togo Toadfoot of Frogmorton
Elvish name: Mablung Miriel
Beyound Arduino Lang
 
wind-pirate

Senior Member

Joined: 01/02/2007
Location: Canada
Posts: 101
Posted: 04:14am 26 Jan 2008
Copy link to clipboard 
Print this post

Do the tests at the battery holder. No need to solder to the board.
Ron
THE Pirate.
stealing wind & solar energy is fun
 
vasi

Guru

Joined: 23/03/2007
Location: Romania
Posts: 1697
Posted: 02:51am 01 Feb 2008
Copy link to clipboard 
Print this post

Very good ideea,

Solar lamp but inside.
Hobbit name: Togo Toadfoot of Frogmorton
Elvish name: Mablung Miriel
Beyound Arduino Lang
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024