Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 00:12 11 Dec 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : EV's : garden tractor

Author Message
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 10:37am 17 Jan 2024
Copy link to clipboard 
Print this post

Based on a John Deere type, I wanted to make a usable electric garden tractor.
Started with the flanges of the rear wheels.


 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 11:29am 17 Jan 2024
Copy link to clipboard 
Print this post

Shaping the axles.

 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 11:05am 18 Jan 2024
Copy link to clipboard 
Print this post

The scale is approximately 1:5 so that the tractor can really be used for work in the garden.

 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 12:37pm 18 Jan 2024
Copy link to clipboard 
Print this post

A set up with a 36 volt motor.


Edited 2024-01-19 06:57 by jorn
 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 10:21am 19 Jan 2024
Copy link to clipboard 
Print this post

For a smaller turning circle I made a narrowfront-axle.

 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 11:40am 20 Jan 2024
Copy link to clipboard 
Print this post

In my tractor model actually fits a water-cooled 4-cylinder engine. That's why I thought about a 4 cyl. solenoid.
I started with a 1 cylinder test setup.


Edited 2024-01-20 21:43 by jorn
 
Revlac

Guru

Joined: 31/12/2016
Location: Australia
Posts: 1031
Posted: 12:15am 21 Jan 2024
Copy link to clipboard 
Print this post

Nice work,  solenoids do work and the timing could be from the crankshaft etc, but how are you going to limit the power to them, PWM speed comptroller or something better?

Ah found it, you used an electric wheel barrow motor instead.
Edited 2024-01-22 12:21 by Revlac
Cheers Aaron
Off The Grid
 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 10:05am 22 Jan 2024
Copy link to clipboard 
Print this post

The shaping of a four-cylinder solenoid engine for my tractor is an ongoing project with test setups.

 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 10:33am 22 Jan 2024
Copy link to clipboard 
Print this post

Later I mounted on the rear wheels of my tractor  1 motor for each wheel.

 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 09:58am 23 Jan 2024
Copy link to clipboard 
Print this post



It is fun to do all kinds of work with this little tractor.
I want to mount a sickle bar mower with double knife.
 
Revlac

Guru

Joined: 31/12/2016
Location: Australia
Posts: 1031
Posted: 11:00am 23 Jan 2024
Copy link to clipboard 
Print this post

Nice work,
sickle bar mower should work well, they don't take much power to drive them.
Cheers Aaron
Off The Grid
 
jorn
Newbie

Joined: 30/12/2012
Location: Netherlands
Posts: 22
Posted: 03:22pm 13 Feb 2024
Copy link to clipboard 
Print this post

What also comes in very handy is my cart with a low loading floor.

 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024