TheBackShed.com

Forum Index : Microcontroller and PC projects : this display also works ILI9341V

Author

Message

tenij000
Regular Member

Joined: 30/05/2025
Location: Netherlands
Posts: 51

Posted: 07:09pm 28 Jun 2025

Copy link to clipboard

Print this post

ILI9341V shop

the none touch version i try out

EDNEDN
Senior Member

Joined: 18/02/2023
Location: United States
Posts: 161

Posted: 10:18pm 28 Jun 2025

Copy link to clipboard

Print this post

That looks like a really good deal. It is obviously some promotional deal because they will only let you get 1 at the $.99 price with free shipping.

Thanks for the link!!!!

EDNEDN
Senior Member

Joined: 18/02/2023
Location: United States
Posts: 161

Posted: 08:41pm 11 Jul 2025

Copy link to clipboard

Print this post

Well... Go Figure!!!!

I ordered the display and I also asked my wife to order one.

They didn't send the displays. They sent a teaspoon and some make up brushes.
No electronics at all. And the teaspoon had big scratches and gouges in it.

@tenijooo Did you place an order? Did you get anything?

stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2627

Posted: 08:53pm 11 Jul 2025

Copy link to clipboard

Print this post

I got one with no touch chip. works but bit small to see out

palcal

Guru

Joined: 12/10/2011
Location: Australia
Posts: 1995

Posted: 09:05pm 11 Jul 2025

Copy link to clipboard

Print this post

I ordered 2 with touch but paid about AU$10 for each about US$6.50. Still an OK price.
I got them OK and both no problems.

"It is better to be ignorant and ask a stupid question than to be plain Stupid and not ask at all"

stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2627

Posted: 03:46pm 12 Jul 2025

Copy link to clipboard

Print this post

They come in 2 sizes both same 320x240. mine are years old and were cheap then but they work fine. I like car reversing monitors for small displays but as said no touch.

EDNEDN
Senior Member

Joined: 18/02/2023
Location: United States
Posts: 161

Posted: 03:23am 13 Jul 2025

Copy link to clipboard

Print this post

Ha! My wife got stiffed. I asked her to complain and see if they make it right.

But my order actually got delivered today. I haven't connected it up and tested it yet. But at least they sent 1 of the 2 that was ordered.
Edited 2025-07-13 13:54 by EDNEDN

stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2627

Posted: 05:37pm 13 Jul 2025

Copy link to clipboard

Print this post

EDNEDN said Ha! My wife got stiffed. I asked her to complain and see if they make it right.
.

er... that don't travel the pond.

Mixtel90

Guru

Joined: 05/10/2019
Location: United Kingdom
Posts: 8057

Posted: 06:42pm 13 Jul 2025

Copy link to clipboard

Print this post

Stan: your displays are ILI9341 aren't they? Not ILI9341V. I think that's a newer version. Whether there's any difference I don't know. Also, there are at least two versions of the ILI9341 that I know of, the version numbers are written on them. You have to supply your own backlight transistor and/or series resistor for the early version (pre V 2.0, I think).

Mick

Zilog Inside! nascom.info for Nascom & Gemini
Preliminary MMBasic docs & my PCB designs

stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2627

Posted: 08:04pm 13 Jul 2025

Copy link to clipboard

Print this post

I connected led backlight to 5V, no resistor or prob so far.
why dim it I don't know ... pwm?? it dim enough as is