Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9066
Posted: 08:56pm 07 Sep 2014
Copy link to clipboard
Print this post
This case gets more interesting by the post!
Could it look the same, but have totally different guts perhaps? Edited by Grogster 2014-09-09Smoke makes things work. When the smoke gets out, it stops!
palcal Guru Joined: 12/10/2011 Location: AustraliaPosts: 1804
Posted: 09:31pm 07 Sep 2014
Copy link to clipboard
Print this post
@Frank
Not using Maximite, I have UBW32 version of CMM and it works perfectly with two VGA monitors I have tested it on, and as I said my converter works perfectly when connected to the VGA out of my computer and to my 4.3" composite screen.
Paul."It is better to be ignorant and ask a stupid question than to be plain Stupid and not ask at all"
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9066
Posted: 09:42pm 07 Sep 2014
Copy link to clipboard
Print this post
I know this is probably a silly question, Paul, but do you have the 120R resistors and 914 diodes to deck in your VGA circuit from the UBW32?
...I'm sure you do, but just to check...Smoke makes things work. When the smoke gets out, it stops!
palcal Guru Joined: 12/10/2011 Location: AustraliaPosts: 1804
Posted: 10:06pm 07 Sep 2014
Copy link to clipboard
Print this post
Yes Grogster all is OK. If you get a UBW32 connected up one day check it with your converter if that works with the DSE converter I will get one off you.
Paul."It is better to be ignorant and ask a stupid question than to be plain Stupid and not ask at all"
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9066
Posted: 10:20pm 07 Sep 2014
Copy link to clipboard
Print this post
This is INTENSELY interesting.
I have a main-board almost finished which is 200 x 150 and uses the UBW32 module, so I will see if I can hurry the completion of this, and get the boards done, so I can test this board with a converter.
With the 120R resistors and diodes to deck on the VGA colour lines - even on the UBW32, it should be working fine.
...I don't get why it is not, other then that SPECIFIC adaptor you have.
EDIT: I don't suppose you have(or can borrow) another type of VGA-TV adaptor?
Edited by Grogster 2014-09-09Smoke makes things work. When the smoke gets out, it stops!
palcal Guru Joined: 12/10/2011 Location: AustraliaPosts: 1804
Posted: 11:28pm 07 Sep 2014
Copy link to clipboard
Print this post
No, you guys on The Back Shed are the only people I have contact with regarding Microprocessors. I would gladly buy another one but I want to know it will work first.
Paul."It is better to be ignorant and ask a stupid question than to be plain Stupid and not ask at all"
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9066
Posted: 12:47pm 08 Sep 2014
Copy link to clipboard
Print this post
Understandable.
Smoke makes things work. When the smoke gets out, it stops!
Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Print this post
