 Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me. |
Forum Index : Microcontroller and PC projects : Micromite editor, refresh keycode in edit
| Author | Message | ||||
sagt3k Guru  Joined: 01/02/2015 Location: ItalyPosts: 313 |
Hi Geoff Is there a keycode or escape sequence code to simulate a refresh video when micromite is in editor mode? Thanks |
||||
TassyJim Guru Joined: 07/08/2011 Location: AustraliaPosts: 6273 |
Home key twice should bring it back to the beginning of the file. Jim VK7JH MMedit |
||||
| sagt3k Guru Joined: 01/02/2015 Location: ItalyPosts: 313 |
Unfortunately it, does not work. Try this steps: -connect with putty or ttyemulator with your micronite -after go in edit mode and write your code 1 row ex: 10 goto 10 -press F1 and return in editmode -disconnect your emulator and reconnect -you will see all black, now press twice home buttom. -you don't see the code -while with more rows code yes please try it, or happen only to me? 
|
||||
| WhiteWizzard Guru Joined: 05/04/2013 Location: United KingdomPosts: 2934 |
Confirming that I am seeing this 'issue' with MM+ B23 in TT on Win10. Two lines also comes back 'blank' UNTIL you press a key and then code 're-appeared'. But one line I can not get to 're-appear' yet!! Anyone else seeing this in other MM's? WW |
||||
| sagt3k Guru Joined: 01/02/2015 Location: ItalyPosts: 313 |
My sw that use micromite in remote socket with ethernet support need to reconnect with micromite. The software need to send a command for a total refresh. Thanks for your support. |
||||
Geoffg Guru Joined: 06/06/2011 Location: AustraliaPosts: 3287 |
@WW, what were the steps that you did to reproduce the issue? Geoff Graham - http://geoffg.net |
||||
| WhiteWizzard Guru Joined: 05/04/2013 Location: United KingdomPosts: 2934 |
1> Fired up TT (Win10) with MM+ connected via the Serial Console (i.e. USB-TTL module) 2> Went into editor and typed ONE line of code 3> F1 to save it 4> Back into Editor (code can be seen) 5> Physically disconnected the USB-TTL module 6> Physically reconnected USB-TTL module (TT unresponsive (as expected) since connection got broken) 7> Restablished TT connection so comms with MM+ once again 8> Go into editor and NO CODE i.e. the ONE line of code has vanished Note: I did not try a 'useful' line of code. If I had have done I could have tried running it to see if it was hiding in the background. Will try this later but can't do it right now . . . Please does anyone else see this??? If so, on what firmware/device? WW |
||||
| Geoffg Guru Joined: 06/06/2011 Location: AustraliaPosts: 3287 |
Thanks, I will add it to the list. Geoff Graham - http://geoffg.net |
||||
| sagt3k Guru Joined: 01/02/2015 Location: ItalyPosts: 313 |
Ok ...Thanks Geoff If you need more details I can attach screenshoot and more details Thanks |
||||
 Print this page |
 |
The Back Shed's forum code is written, and hosted, in Australia. | © JAQ Software 2025 |
