Home
JAQForum Ver 20.06
Log In or Join  
Active Topics
Local Time 01:15 17 Apr 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Electronics : Can anyone recommend a reliable source of non fake HY5110's ?

Author Message
Warpspeed
Guru

Joined: 09/08/2007
Location: Australia
Posts: 4406
Posted: 09:45pm 01 Mar 2020
Copy link to clipboard 
Print this post

As the topic says, anyone had good or bad experiences with HY5110 mosfets.

Has anyone actually tested the drain source breakdown voltage (with gate shorted to source).
Cheers,  Tony.
 
mikeb

Senior Member

Joined: 10/04/2016
Location: Australia
Posts: 173
Posted: 05:48am 02 Mar 2020
Copy link to clipboard 
Print this post

Sorry mate,
Haven't even heard of the manufacturer (Huayi Microelectronics) let alone a supplier. I tend to steer clear of any device the usual, reputable, suppliers
(RS Components, Element14, Mouser, Digikey) don't stock.
It's only an N Channel Enhancement Mode MOSFET. Do you have to use it ?

Regards, Mike B.
There are 10 kinds of people in the world.
Those that understand binary and those that don't.
 
Solar Mike
Guru

Joined: 08/02/2015
Location: New Zealand
Posts: 1122
Posted: 06:53am 02 Mar 2020
Copy link to clipboard 
Print this post

Warp, I got a bunch of them from LCSC Electronics some time ago, haven't had any issues to date, but haven't measured the breakdown voltage. LCSC should be a reputable supplier.
If they are low on stock ask for a quote...

Cheers
Mike
Edited 2020-03-02 16:55 by Solar Mike
 
Warpspeed
Guru

Joined: 09/08/2007
Location: Australia
Posts: 4406
Posted: 08:33pm 02 Mar 2020
Copy link to clipboard 
Print this post

Thanks guys.

A friend of mine is having trouble with some HY5110 mosfets purchased from LCSC blowing up, and one possibility of several, is that the mosfets are below spec.

I have in the past had some serious drama that was eventually traced to counterfeit fake parts either not working, or that failed very quickly. I have not so far used HY5110's myself but recall that others here have, so was just wondering...

Have to agree though that LCSC from all accounts so far, seem to be a reputable source.
Cheers,  Tony.
 
nickskethisniks
Guru

Joined: 17/10/2017
Location: Belgium
Posts: 409
Posted: 11:26am 04 Mar 2020
Copy link to clipboard 
Print this post

Maybe irf100p218 is an alternative?
 
poida

Guru

Joined: 02/02/2017
Location: Australia
Posts: 1387
Posted: 11:37pm 18 Apr 2020
Copy link to clipboard 
Print this post

  Warpspeed said  As the topic says, anyone had good or bad experiences with HY5110 mosfets.

Has anyone actually tested the drain source breakdown voltage (with gate shorted to source).


I just did.
I tested both the HY5110 and the HY4008.
Both tests with about 30mA current limited by series resistor.

HY5110 Vds 109V
HY4008 Vds 85V

The specs for Vds breakdown usually use 250uA.
The test had a 3.2K 7W resistor in series, so I measure  the breakdown voltage
when 0.8V across the 3.2K R
wronger than a phone book full of wrong phone numbers
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024