Menu
JAQForum Ver 26.09

Forum Index : Microcontroller and PC projects : Colour Maximite 2 G3

   Page 1 of 2    
Posted: 03:41pm
15 Nov 2026
Copy link to clipboard
matherp
Guru

The Colour Maximite 2 with HDMI. Full details on https://mather.host/cmm2/g3/
The G3 is a G2 whose picture goes to an HDMI transmitter instead of VGA, and whose sound plays through the HDMI screen and the audio socket at the same time. Everything else is the G2's, so G2 programs and add-ons work on it unchanged.



The final design files reference in the web page have a two pin header by the on/off switch do you can omit the switch if required and jumper the header or use it to connect a separate switch.
 
Posted: 04:01pm
15 Nov 2026
Copy link to clipboard
Mixtel90
Guru


Brilliant work yet again, Peter. :)
You've even managed to make javavi happy. :)
 
Posted: 04:58pm
15 Nov 2026
Copy link to clipboard
terekgabor
Senior Member

I ordered a G2 one hour before    
 
Posted: 05:01pm
15 Nov 2026
Copy link to clipboard
Mixtel90
Guru


Of course. It always works out like that. :)
 
Posted: 09:46am
16 Nov 2026
Copy link to clipboard
terekgabor
Senior Member

I was lucky, they can't deliver to EU.
I refunded the money.
Go with G3.
 
Posted: 09:18pm
17 Nov 2026
Copy link to clipboard
Volhout
Guru


Peter,

When you move the CR2032, you can put the RM2 module on the G3 main board.

Volhout
 
Posted: 07:56am
18 Nov 2026
Copy link to clipboard
Grogster
Admin Group


Good point.

I 2nd that idea.....  
 
Posted: 08:30am
18 Nov 2026
Copy link to clipboard
Wölfi
Regular Member


Is an ESP-01 still necessary when an RM2 is integrated, or has it just become obsolete?
 
Posted: 09:06am
18 Nov 2026
Copy link to clipboard
Mixtel90
Guru


You could use it as well, if you wanted to. It's on COM2 so there is no conflict. You might want to access two different networks or maybe use it as a RF link to another one somewhere else on their own private RF link.

What you can't do is use the same commands for the RM2 and ESP-01. They are completely different devices.
 
Posted: 09:40am
18 Nov 2026
Copy link to clipboard
Wölfi
Regular Member


Thanks, good to know!
 
Posted: 10:02am
18 Nov 2026
Copy link to clipboard
matherp
Guru

I will look at the wifi suggestion. In the meantime I suggest no-one gets any G3 boards made as the change needed is quite large and it will change pinouts on the edge connector
 
Posted: 05:33pm
18 Nov 2026
Copy link to clipboard
matherp
Guru

Fully built @ 60USD each + shipping and any applicable taxes

Edited 2026-11-19 03:53 by matherp
 
Posted: 07:34pm
18 Nov 2026
Copy link to clipboard
WhiteWizzard
Guru

This looks really good - just two questions (for now):

1) what’s the reasoning behind having a full size SD card that takes up more real-estate on the PCB

2) could you task Claude with generating a ‘comparison chart’ between this new G3 and the PC3.

The reason for the second point is that I really don’t currently know which is the better of the two based on your continuous hardware improvements and new software features. With a comparison chart people would be better placed to make an informed decision.

Just a few examples of my confusion which can hopefully be resolved is regarding whether MicroPython would be better on the G3 or the PC3. And can Doom (plus the other ‘games’) be run on both, likewise the emulators.

I know the information is contained in multiple threads and posts, but by the time things are found, the beast has a new feature!

Hopefully I’m not the only one that would benefit from a comparison…….

Thanks - really liking this G3, and the PC3, but which to invest in first??!!  
 
Posted: 08:47pm
18 Nov 2026
Copy link to clipboard
homa
Guru


  WhiteWizzard said  ...
Thanks - really liking this G3, and the PC3, but which to invest in first??!!  

You need both

Peter, thank you so much! So, does that mean version 1.2 has been released?

Matthias
 
Posted: 11:45pm
18 Nov 2026
Copy link to clipboard
PhenixRising
Guru

Still has provision for ESP-01?
 
Posted: 12:19am
19 Nov 2026
Copy link to clipboard
phil99
Guru


Bottom left of PCB above.
 
Posted: 06:58am
19 Nov 2026
Copy link to clipboard
toml_12953
Guru

When I send the Gerbers, BOM and CPL to JLCPCB, I get this error message

The BOM file doesn't match the CPL file, please check and re-upload the files.

I tried three times, just in case I was inadvertently sending an incorrect file. I got the same error message each time.
 
Posted: 07:47am
19 Nov 2026
Copy link to clipboard
PhenixRising
Guru

  phil99 said  Bottom left of PCB above.


Hi Phil,

That is what I was referring to but I thought it was being superseded by the RM2 module.
 
Posted: 07:54am
19 Nov 2026
Copy link to clipboard
matherp
Guru

  Quote   could you task Claude with generating a ‘comparison chart’ between this new G3 and the PC3.

https://mather.host/blog/pc3-or-cmm2-g3/

  Quote  In the meantime I suggest no-one gets any G3 boards made as the change needed is quite large and it will change pinouts on the edge connector.

I don't post files for relatively expensive builds like this until I have had some made and tested them. I'm away for the next couple of weeks so I won't be making the V1.2 files with the onboard RM2 available until after that
 
Posted: 08:19am
19 Nov 2026
Copy link to clipboard
PhenixRising
Guru

  matherp said  
https://mather.host/blog/pc3-or-cmm2-g3/



  Quote  but the RP2350's Cortex-M33 has hardware only for single precision, so each double takes a software routine.


Is the following a correct statement and worth mentioning?

  Quote  However, where speed is more important than precision, embedded C allows the use of single precision which results in a dramatic speed-boost.

Edited 2026-11-19 18:20 by PhenixRising
 
   Page 1 of 2    
The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026