Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 13:00 20 Dec 2025 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 191738 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 509513   02:49pm 16 Dec 2015
Normal Topics  

   Page 34 of 98    

Exmork owners or machanics brucedownunder2, 16/01/2011 12 13686   05:13am 23 Jan 2011
Uploading photos redbullalan, 23/01/2011 2 3866   08:53pm 22 Jan 2011
Power regulators /charge controller plea redbullalan, 17/01/2011 8 8367   02:37pm 22 Jan 2011
A fantastic site THANK YOU redbullalan, 17/01/2011 1 4754   06:44pm 21 Jan 2011
Multiple mill location Rastus, 20/01/2011 4 6176   01:46pm 21 Jan 2011
Big motor help redbullalan, 18/01/2011 2 6351   09:57am 20 Jan 2011
Petes’s AXFX Downwind, 13/10/2010 29 31287   09:30am 20 Jan 2011
make a decision for me kevindion, 15/01/2011 4 6457   12:46pm 15 Jan 2011
DIY Wind Tubine Charge Controller powerbox, 31/12/2010 14 23752   03:16pm 13 Jan 2011
Are Solar Charge Controllers any good? paul_mac1, 10/01/2011 3 6898   02:20am 12 Jan 2011
2.9M White Pointer Review Greenthumbs, 19/12/2010 8 10722   01:29am 12 Jan 2011
Wind mill DC motor concordpond, 11/01/2011 1 4994   11:29pm 10 Jan 2011
variation on Oztules blades niall1, 08/01/2011 4 6980   03:58am 09 Jan 2011
i made some mistakes kevindion, 04/01/2011 8 7560   01:08pm 05 Jan 2011
what volt,7x2c treecare, 03/01/2011 1 4536   07:26am 05 Jan 2011
Windspeed data GWatPE, 02/01/2011 11 7468   11:17pm 03 Jan 2011
windmills treecare, 02/01/2011 7 7171   10:34am 03 Jan 2011
5phasePma100T 3phasePma125T 3phasePma70T faroun, 03/01/2011 0 4804   01:57am 03 Jan 2011
3phase 14awg VS 3phase 18awg PMA’s faroun, 01/01/2011 2 6293   12:10am 01 Jan 2011
Star?delta ? WindyMick, 27/12/2010 10 7008   11:10am 31 Dec 2010
65mph/29 ms winds, mill down JimBo911, 24/06/2010 24 24438   07:49am 31 Dec 2010
Windmill>Turbine reg>PVE1200 WindyMick, 25/12/2010 6 7050   06:33am 31 Dec 2010
my first windmill kevindion, 22/12/2010 2 5874   12:34pm 27 Dec 2010
F&P w/Extruded Blades flying Steve9R, 26/12/2010 6 7343   12:01pm 27 Dec 2010
NEW better Chinese blades, with our help. Gizmo, 03/10/2008 58 72079   01:55pm 24 Dec 2010
= New posts since you last visited .      

   Page 34 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2025