TheBackShed.com

Home	JAQForum Ver 24.01
Log In or Join
Active Topics
Local Time 21:18 29 Jul 2025	Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Windmills

New Topic

	Topics	Started By	Replies	Views	Last Post By
Sticky Topics
	Forum upgrade	Gizmo, 05/07/2019	306	177205	Chopperp 08:58am 07 May 2025
	Forum Guidelines	Gizmo, 11/12/2011	2	496486	02:49pm 16 Dec 2015
Normal Topics			Page 64 of 98
	New PVC blades.	Gizmo, 01/10/2007	15	31860	02:59pm 11 Jan 2009
	Dimensions of 6005 bearing	caesius, 08/01/2009	2	3603	09:15pm 07 Jan 2009
	Make full set of blades in one go!	KiwiJohn, 07/01/2009	0	3357	06:56am 07 Jan 2009
	Selenoid alternator	gj4533, 02/01/2009	4	2693	12:10pm 02 Jan 2009
	Grid Tied Inverter?	Wes Lemarr, 02/01/2009	1	2361	05:24pm 01 Jan 2009
	Some thoughts on Power Factor etc etc	KiwiJohn, 01/01/2009	12	3438	07:56am 01 Jan 2009
	Setting up a new windmill.	Bluey, 31/12/2008	1	2630	10:13am 31 Dec 2008
	Frequency Switch for star / delta ?	BUGS, 30/12/2008	2	2998	09:28pm 30 Dec 2008
	Kitset Mills?	andrewf, 27/12/2008	1	2727	05:50pm 27 Dec 2008
	small commercial turbine design	Gavztheouch, 23/12/2008	4	3543	04:09am 25 Dec 2008
	Newbie Grid connect windmill idea	Greenthumbs, 05/12/2008	8	5387	03:37am 23 Dec 2008
	It’s that time of year again.	Gizmo, 20/12/2008	7	3120	11:29pm 22 Dec 2008
	My router copy machine.	KiwiJohn, 19/12/2008	6	6636	11:49pm 20 Dec 2008
	Chinese unit up and working	Bushman, 20/12/2008	1	2632	03:26am 20 Dec 2008
	200 Watt Jaycar Mill	hydroplasma, 19/12/2008	1	3008	11:55pm 19 Dec 2008
	Quad Rebuild	fillm, 05/12/2008	10	6284	11:51am 19 Dec 2008
	Government Rebate on Windmills	Jarbar, 17/12/2008	3	3360	01:38pm 18 Dec 2008
	Wind turbine blades	lukejj, 16/12/2008	2	3137	04:49am 18 Dec 2008
	Bad weekend for the windmill.	Gizmo, 15/12/2008	2	5477	10:51am 17 Dec 2008
	Need help getting started	RealtyRoy, 04/12/2008	6	3231	09:56pm 08 Dec 2008
	Working on a 10 hp motorconversion	Dinges, 10/07/2008	91	42024	06:35pm 08 Dec 2008
	Quad Stator- "BEAST" - KABOOM!!!	fillm, 29/11/2008	17	9737	03:04pm 08 Dec 2008
	Measuring Generator Kwh Output?	Wes Lemarr, 08/12/2008	9	8732	08:26am 08 Dec 2008
	Is it safe to run an F&P without a load?	Mr.Sleepy, 04/12/2008	7	3639	09:40am 06 Dec 2008
	hi iam new here	rolfkoedam, 14/11/2008	5	3749	06:44pm 03 Dec 2008
= New posts since you last visited .

Page 64 of 98