Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 11:34 06 May 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 202679 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 519234   02:49pm 16 Dec 2015
Normal Topics  

   Page 72 of 99    

testbed setup some testing done brucedownunder2, 20/04/2008 14 5343   10:02am 10 Jul 2008
Need some help with mini windmill jeen, 06/07/2008 26 12074   07:22am 10 Jul 2008
using a stepper motor? mahela007, 08/07/2008 1 4267   03:18am 08 Jul 2008
lg motors prophetski, 06/07/2008 3 3880   01:34pm 07 Jul 2008
how to figure out different volt coils/st newbie-from-pa, 29/06/2008 3 3445   11:55am 07 Jul 2008
charging AA batteries? mahela007, 06/07/2008 3 4028   03:53am 07 Jul 2008
Wooden Blade Carving Bryan1, 30/03/2008 24 9824   09:59am 06 Jul 2008
Australia BBDrums, 03/07/2008 4 4634   04:00pm 05 Jul 2008
Windmill thrust loading rber, 04/07/2008 3 4364   06:11pm 04 Jul 2008
towers BBDrums, 03/07/2008 6 3432   12:18pm 04 Jul 2008
magnets to stator count hoodlem, 02/07/2008 7 3605   01:15pm 03 Jul 2008
3kW Generator Unit Jason69, 04/07/2007 16 6165   04:41am 03 Jul 2008
The test bed brucedownunder2, 01/07/2008 2 3305   11:15pm 01 Jul 2008
BRUSH LOSSES FandPwithPVC, 24/06/2008 9 4805   11:33pm 30 Jun 2008
Maines got wind also BBDrums, 29/06/2008 11 3245   06:11pm 30 Jun 2008
alternator for low rpm mechamz, 29/06/2008 10 3758   11:06am 30 Jun 2008
Vertical axis windmill question Merlino, 25/06/2008 8 3580   03:46pm 27 Jun 2008
Pipe coupling imsmooth, 24/06/2008 5 4367   09:51am 27 Jun 2008
is this the right fisher & paykel washer? Jpm000001, 25/06/2008 2 3437   12:49pm 25 Jun 2008
Books about vertical axis windmills Merlino, 24/06/2008 1 3588   02:50am 25 Jun 2008
Undergearing + Multipal Stators Hybrid, 08/06/2008 22 7423   05:14pm 23 Jun 2008
motor advice needed for beginner JW1111, 19/06/2008 4 3825   01:44am 23 Jun 2008
The Ugly Duckling sodes, 19/06/2008 10 9423   12:36pm 22 Jun 2008
Furling moe46, 21/06/2008 13 10130   04:28am 22 Jun 2008
Single blade windmill davef, 15/06/2008 12 6018   11:37pm 20 Jun 2008
= New posts since you last visited .      

   Page 72 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026