 Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me. |
Forum Index : Microcontroller and PC projects : I've now jumped on the PICO2 train...
| Author | Message | ||||
Grogster Admin Group  Joined: 31/12/2012 Location: New ZealandPosts: 9573 |
I have some on order.  This module looks very nice indeed. Good job, Peter.  As with everyone else's orders, the PSRAM chip was unavailable, so I just left it off. I HOPE....I can get some time to play with this new module. I am very busy at work these daze.....  Smoke makes things work. When the smoke gets out, it stops! |
||||
Bryan1 Guru  Joined: 22/02/2006 Location: AustraliaPosts: 1403 |
Grog's if you one spare I'll buy one off you mate Cheers Bryan |
||||
| Bleep Guru Joined: 09/01/2022 Location: United KingdomPosts: 613 |
Make sure you set up the R1V pot before you power anything on. |
||||
| matherp Guru Joined: 11/12/2012 Location: United KingdomPosts: 10169 |
The pots seem to come mid-range which gives a voltage of just over 1.4 - perfectly safe. I just power the boards up and then with a multimeter across DVDD and GND adjust to 1.3. The board is designed so that even with the pot full scale it should be safe (1.8V) - others have run the chip at that without issue |
||||
| PhenixRising Guru Joined: 07/11/2023 Location: United KingdomPosts: 1307 |
Started laying out a carrier board. DIL is soo nice. |
||||
| Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9573 |
I will ensure pot is mid-range first, then do the power check thing. I have to do a bit more research on Peter's original thread. I can't remember what the purpose of the little trimmer is, but I am sure it is there for good reason. None of the other boards have it, so perhaps it is specific to the 2350 chip or something - I will go do a bit more reading to find out. JLC website DID moan that the oscillator and caps were NOT those specifically stated by Raspberry PI Org that you are supposed to use, but I basically ignored it, assuming Peter knows what he's doing with PI boards now, and I have also seen posts from others who have had these boards made, and they obviously start up fine, so.... Smoke makes things work. When the smoke gets out, it stops! |
||||
| Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9573 |
Yes, I ordered ten units, so I will have a few spares - I'll only be playing with one module to start with. I may well put them up on my website, so long as Peter is happy with the state of the design etc, and if other members think that would be something they would like me to do. Smoke makes things work. When the smoke gets out, it stops! |
||||
| Bryan1 Guru Joined: 22/02/2006 Location: AustraliaPosts: 1403 |
Thanks Grog's when your ready to send one over just PM me with the cost and I'll make the payment straight away. |
||||
| robert.rozee Guru Joined: 31/12/2012 Location: New ZealandPosts: 2426 |
is the unused end of R1V tied to the wiper? i'd be interested in seeing both sides of the PCB with parts unpopulated so all tracks are visible. cheers, rob :-) |
||||
| matherp Guru Joined: 11/12/2012 Location: United KingdomPosts: 10169 |
Grogster et al I have done a trivial update to include GPIO numbers on the top silkscreen of the board. No other changes. The board as you have ordered seems rock solid. Pico2350DILV1.2.zip  Edited 2025-06-14 17:17 by matherp |
||||
| Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9573 |
Excellent. I have yet to test my units as ordered, but if Peter is happy(and it seems he is) with the stability of this layout, I will PROBABLY offer these for sale on my website. Shipping world-wide. Smoke makes things work. When the smoke gets out, it stops! |
||||
| Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9573 |
One of the things I want to do, is design a carrier board that has HDMI. PhenixRising has already indicated this is in progress, so rather then double-up, perhaps the member can elaborate on what they are going to have on their carrier board? No sense in re-inventing the wheel..... Smoke makes things work. When the smoke gets out, it stops! |
||||
| PhenixRising Guru Joined: 07/11/2023 Location: United KingdomPosts: 1307 |
Hi Grogs, Mine is purely for machine interfacing. -16 buffered ins -16 buffered outs -2 MC3486 line receivers -2 4050 level shifters -1 op-amp for analog out -1 MAX3491 for multidrop, FD RS422. etc.... |
||||
 Print this page |
 |
The Back Shed's forum code is written, and hosted, in Australia. | © JAQ Software 2025 |
