Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
|
Forum Index : Microcontroller and PC projects : Pi-Cromite 1B PCB...
Page 3 of 4 | |||||
Author | Message | ||||
flip Senior Member Joined: 18/07/2016 Location: AustraliaPosts: 114 |
Cheers...done... |
||||
paceman Guru Joined: 07/10/2011 Location: AustraliaPosts: 1327 |
Mine arrived today Grogs (12/9). Thanks very much - now to get it going. Greg |
||||
MikeO Senior Member Joined: 11/09/2011 Location: AustraliaPosts: 275 |
Arrived , Thank you. Mike Codenquilts |
||||
atmega8 Guru Joined: 19/11/2013 Location: GermanyPosts: 712 |
Arrived yesterday ! Thank you for this nice PCB's Grogster. Dietmar |
||||
bigmik Guru Joined: 20/06/2011 Location: AustraliaPosts: 2870 |
Mine Arrived today, Thank you Grogster.. Much appreciated Kind Regards, Mick Mick's uMite Stuff can be found >>> HERE (Kindly hosted by Dontronics) <<< |
||||
astroboy Newbie Joined: 28/12/2014 Location: AustraliaPosts: 38 |
Mine arrived on Monday. Thanks Grogster. Regards John |
||||
Bill7300 Senior Member Joined: 05/08/2014 Location: AustraliaPosts: 158 |
Since everybody else is reporting, I maybe should do the same. My pair arrived yesterday, thanks Grogs. Bill Bill |
||||
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9063 |
Thanks for all the confirmations thus far, chums. I'd better build one myself then, hadn't I?! (rhetorical!) Smoke makes things work. When the smoke gets out, it stops! |
||||
RonnS Senior Member Joined: 16/07/2015 Location: GermanyPosts: 120 |
I got it yesterday, the PCB looks very good thank you very much Ron |
||||
atmega8 Guru Joined: 19/11/2013 Location: GermanyPosts: 712 |
Help needed, i have ordered a 2.8" inch mit Touchscreen TFT LCD Display ILI9341 Arduino AVR CP11005 attached it to Grogs Backpack, used OPTION lcdpanel ILI9341,L,29,3,13. SPI LCD Poti is mounted also 33R Resistor. Can measure 3,3 an 4,7 Volts. Power upply via the oauter corner USB. Whatever i do, the Display stays dark, no output... Any suggestions, Tips for me? THX Atmega8 |
||||
atmega8 Guru Joined: 19/11/2013 Location: GermanyPosts: 712 |
NO 4k7 Pullups soldered! > option list OPTION COLOURCODE ON OPTION LCDPANEL ILI9341, LANDSCAPE, 29, 31, 13 OPTION WAVETIME 1.222 > gui test lcdpanel > > GUI CHECKBOX #10, "rztrtz", 100, 100, 50, rgb(BLUE) > print mm.ver 5.04 > |
||||
RonnS Senior Member Joined: 16/07/2015 Location: GermanyPosts: 120 |
"" 2.8" inch mit Touchscreen TFT LCD Display ILI9341 Arduino AVR CP11005 "" is an parallel driven LCD ! not an SPI ! its not supported by the PiCromite but see here: http://www.thebackshed.com/forum/forum_posts.asp?TID=9771&get=last#109377 |
||||
atmega8 Guru Joined: 19/11/2013 Location: GermanyPosts: 712 |
Ok, seems I have ordered the wrong display..;-((? |
||||
matherp Guru Joined: 11/12/2012 Location: United KingdomPosts: 8583 |
This display uses a 16-bit parallel I/F so not really do-able in the Pi and in any event Grogster's board doesn't have any connections for DB8-DB15. |
||||
atmega8 Guru Joined: 19/11/2013 Location: GermanyPosts: 712 |
Peter, what kind of Display are you using in the post from 31. August? Do you have a source where to buy it? THX Dietmar |
||||
matherp Guru Joined: 11/12/2012 Location: United KingdomPosts: 8583 |
I get them off ebay, search for ILI9341 2.8" just make sure the version you buy has the touch controller |
||||
Frank N. Furter Guru Joined: 28/05/2012 Location: GermanyPosts: 813 |
Hi Grogster, my PCB's arrived today - thank you very much! Frank |
||||
flip Senior Member Joined: 18/07/2016 Location: AustraliaPosts: 114 |
My 2 came Friday as well...thanks Grogster. Phil |
||||
bigfix Senior Member Joined: 20/02/2014 Location: AustriaPosts: 124 |
My PCBs arrived yesterday - thanks ! Guenter |
||||
Grogster Admin Group Joined: 31/12/2012 Location: New ZealandPosts: 9063 |
No lost boards yet - that's good news. Smoke makes things work. When the smoke gets out, it stops! |
||||
Page 3 of 4 |
Print this page |