TheBackShed.com

Home	JAQForum Ver 24.01
Log In or Join
Active Topics
Local Time 09:08 06 Aug 2025	Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Windmills

New Topic

	Topics	Started By	Replies	Views	Last Post By
Sticky Topics
	Forum upgrade	Gizmo, 05/07/2019	306	177719	Chopperp 08:58am 07 May 2025
	Forum Guidelines	Gizmo, 11/12/2011	2	496931	02:49pm 16 Dec 2015
Normal Topics			Page 54 of 98
	Newbie question	klakka, 16/08/2009	1	2838	03:55pm 16 Aug 2009
	Tons of Research on Bearings	node4, 15/08/2009	5	3963	11:54am 16 Aug 2009
	what diode?	daggit, 14/08/2009	7	3759	12:15pm 14 Aug 2009
	My first windmill complete	AMACK, 05/08/2009	21	8490	03:08am 13 Aug 2009
	wind mill controller need - help !	remuda, 27/06/2009	9	4453	05:54pm 11 Aug 2009
	Harvesting all or most of the power from	Wes Lemarr, 02/08/2009	11	4190	12:50am 09 Aug 2009
	Weather station software for wind users	Bolty, 14/07/2009	12	13026	12:36am 09 Aug 2009
	Huge stockpile of used motors!!	daggit, 08/08/2009	3	3092	05:03pm 08 Aug 2009
	Home based power options?	takagari, 30/07/2009	3	3519	03:53pm 08 Aug 2009
	vawt	xr40, 29/07/2009	9	4240	12:47pm 08 Aug 2009
	Noob takin a shot at wind power	daggit, 04/08/2009	5	3747	01:51am 08 Aug 2009
	average daily wind power output	imsmooth, 01/08/2009	2	3148	09:16pm 05 Aug 2009
	commercial direct-drive turbines (~1MW)	Dinges, 05/08/2009	5	3520	09:12pm 05 Aug 2009
	Furling vs. Changing Pitch	Pukwudji, 28/07/2009	9	4221	09:33am 02 Aug 2009
	Quietrevolution	MacGyver, 29/07/2009	0	2952	05:11am 29 Jul 2009
	Car tailshaft spline suits the F&P shaft	Gizmo, 24/09/2006	5	3812	02:49am 28 Jul 2009
	my Lenz2 attempt	gj4533, 28/12/2008	56	25424	12:20pm 26 Jul 2009
	windmills	mrdd, 26/07/2009	1	3158	01:23am 26 Jul 2009
	Neo’s Finally Installed	JimBo911, 21/07/2009	11	3388	01:00pm 25 Jul 2009
	F&P source in the States	Pukwudji, 10/07/2009	18	7330	03:01am 25 Jul 2009
	The "Ax Fx - & - F&P Dual"	fillm, 11/07/2009	9	13986	10:42pm 24 Jul 2009
	Round Neos for wind turbine	Bryan1, 19/07/2009	3	3538	10:28pm 24 Jul 2009
	PVC Extruded blades feedback?	Gizmo, 05/07/2009	21	8854	03:36am 24 Jul 2009
	F&P and Oasis	readyakira, 22/07/2009	9	3400	02:17am 23 Jul 2009
	Furling	Smart Drives, 17/07/2009	10	3443	09:38pm 21 Jul 2009
= New posts since you last visited .

Page 54 of 98