Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 14:21 02 Jan 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Microcontroller and PC projects
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 192778 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 510413   02:49pm 16 Dec 2015
Photos Geoffg, 28/01/2019 135 52624 lizby  12:40am 01 Jan 2026
Part suppliers. Gizmo, 10/01/2016 30 71618 WhiteWizzard  12:32pm 03 May 2025
Micromite MMBasic Library(s) Gizmo, 14/12/2014 1 82577 lizby  03:55pm 26 Nov 2021
Read Me. Guidelines for this section. Gizmo, 24/11/2011 7 66676 GregZone  09:03pm 06 Jun 2020
Normal Topics  

   Page 179 of 444    

CMM2: Fill Command? vegipete, 30/11/2020 9 2883 William Leue  03:19pm 07 Dec 2020
Settick lew247, 06/12/2020 14 2185 lizby  08:19pm 06 Dec 2020
Sprite show and scan lines RCMAN, 05/12/2020 2 1960 RCMAN  05:16pm 06 Dec 2020
Question about keyboard input RCMAN, 07/12/2020 4 1643 RCMAN  04:39pm 06 Dec 2020
Kindly request for EDITOR jirsoft, 06/12/2020 2 2064 jirsoft  04:35pm 06 Dec 2020
MAXIMITE 2 R-2R resistor values electricat, 04/12/2020 6 2033 electricat  10:21pm 05 Dec 2020
CMM2: V5.06.00b7 - 3D engine matherp, 29/11/2020 114 7892 TassyJim  09:07pm 05 Dec 2020
Sticky keys jirsoft, 05/12/2020 5 2306 jirsoft  06:44pm 05 Dec 2020
MMBasicCFunctions.pdf yock1960, 05/12/2020 4 2305 JohnS  02:37pm 05 Dec 2020
Is this possible lew247, 04/12/2020 20 4135 lew247  10:17am 05 Dec 2020
CMM2: GETSCANLINE TassyJim, 28/11/2020 9 2711 George H  01:42am 05 Dec 2020
CMM2: 3D Object Viewer vegipete, 30/11/2020 5 2818 MauroXavier  05:51pm 04 Dec 2020
Maximite 2: How to make switch trigger only once when pressed Decoy, 30/11/2020 17 2994 Tinine  06:37am 03 Dec 2020
4 state linear automata yock1960, 26/11/2020 5 2384 yock1960  01:51am 03 Dec 2020
Don't laugh! yock1960, 02/12/2020 10 3034 yock1960  07:08pm 02 Dec 2020
No Print Zones??? toml_12953, 01/12/2020 13 2670 JohnS  05:41pm 02 Dec 2020
MM+ 100pin with SSD1963 in 16bit mode panky, 01/12/2020 7 2902 matherp  03:05pm 02 Dec 2020
2.8" TFT LCD Wall Display MikeO, 02/12/2020 3 3066 CaptainBoing  07:48am 02 Dec 2020
No More Errors toml_12953, 02/12/2020 0 1694 toml_12953  01:59am 02 Dec 2020
MM+: Yeah, pause for serial comms...... Grogster, 30/11/2020 5 1835 Grogster  03:59am 01 Dec 2020
Mode command locks up cmm2 qwerty823, 01/12/2020 4 2061 qwerty823  03:05am 01 Dec 2020
Default Location for Programs? toml_12953, 01/12/2020 1 1815 TassyJim  02:32am 01 Dec 2020
I just wanted to say lew247, 01/12/2020 4 1896 Tinine  12:48am 01 Dec 2020
What am I doing wrong lew247, 20/07/2020 38 6564 disco4now  10:17pm 30 Nov 2020
CMM2 Diagnostics Available? toml_12953, 30/11/2020 15 2095 Paul_L  07:23pm 30 Nov 2020
= New posts since you last visited .      

   Page 179 of 444    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026