Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 23:36 02 May 2025 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 303 170253 Gizmo  03:34am 02 May 2025
Forum Guidelines Gizmo, 11/12/2011 2 490628   02:49pm 16 Dec 2015
Normal Topics  

   Page 3 of 98    

Vibrating generator. Pauld, 05/06/2022 10 3512 Pauld  07:48am 29 Jul 2022
Number of Blades To Install In a Wind Turbine - Three or SIX? (!) Technophiliac, 12/07/2022 0 3108 Technophiliac  05:04am 12 Jul 2022
Tailless Wind Turbine Design - A look into the Future?! Technophiliac, 07/04/2022 0 4052 Technophiliac  11:20pm 06 Apr 2022
Very simple furling design needed tommydog, 04/04/2022 2 3376 tommydog  12:28pm 04 Apr 2022
Does re-phasing reduce required tourqe input? Offgridguy, 04/04/2022 0 3206 Offgridguy  11:07am 04 Apr 2022
Does re-phasing reduce required tourqe input? Offgridguy, 04/04/2022 0 3171 Offgridguy  11:06am 04 Apr 2022
Rotary Screw Air compressor wind Genny Bryan1, 16/01/2022 5 4454 Bryan1  03:20am 21 Feb 2022
Windmills for hot water KiwiJohn, 19/07/2006 46 39324 Pierre159  08:22pm 31 Jan 2022
Suitable clutch plate to fit Fisher and Paykel smart drive spline noodlepringle, 03/06/2021 12 6896 fillm  08:08am 31 Jan 2022
yet another F&P VAWT but take a look at the 3D rotor program johngeraint, 18/11/2021 2 5015 scruss  01:32pm 18 Nov 2021
Would this washer have a stepper motor? heynow999, 19/02/2009 3 6180 colbingracie  07:19am 26 Oct 2021
12V 900W Turbine - Splitting the Load Over 2 Controllers? Technophiliac, 15/04/2021 35 8752 Godoh  11:16pm 25 Oct 2021
Single Phase Fisher & Pykel Rastus, 01/10/2021 25 6731 Rastus  01:04pm 06 Oct 2021
New EAZWind wind generators rogerdw, 26/09/2021 1 4996 Wynpust  08:46am 03 Oct 2021
Long Distance Wind Turbine 00fGrid, 25/07/2021 17 6484 Clockmanfr  08:49am 02 Sep 2021
wind generator on e bay brucedownunder2, 31/07/2021 0 4344 brucedownunder2  02:35am 31 Jul 2021
Physical/Hydraulic/Electromechanical Braking of Turbines? Kamak, 20/04/2021 26 8250 Kamak  04:11am 11 May 2021
BLDC DD 3-Phase AC Induction Generator Build Kamak, 17/04/2021 70 9234 Kamak  02:59pm 06 May 2021
Why Not In Reverse? Kamak, 05/05/2021 3 4521 Kamak  03:58am 06 May 2021
Swapping out the stock magnets? Kamak, 14/04/2021 17 5955 Kamak  03:48am 06 May 2021
Has Anyone Ever Figured It Out? Kamak, 21/04/2021 1 4641 kitestrings  12:32am 04 May 2021
So, how would you go about removing the stock magnets from the rotor? Kamak, 23/04/2021 2 4496 Kamak  12:36am 27 Apr 2021
Made to be High Voltage Low Current Kamak, 25/04/2021 5 5642 Kamak  03:59am 25 Apr 2021
Importance of Balanced Load on Phases on Wind Turbines? Technophiliac, 21/04/2021 4 5318 Kamak  05:30pm 22 Apr 2021
Motor Winding Wire Gauge Sizing as per Good rule of Thumb Approach Kamak, 21/04/2021 0 5205 Kamak  05:22am 21 Apr 2021
= New posts since you last visited .      

   Page 3 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2025