Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 21:22 06 Feb 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 195823 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 513074   02:49pm 16 Dec 2015
Normal Topics  

   Page 49 of 98    

My gen controls Dupa, 14/12/2009 3 3572   03:33am 18 Dec 2009
building my first wind gen zippy998, 14/12/2009 6 4097   09:57pm 17 Dec 2009
ac motors zippy998, 17/12/2009 2 3483   03:47pm 17 Dec 2009
Dump Into Outdoor wood boiler Dupa, 09/12/2009 8 4390   09:46pm 16 Dec 2009
Hello! Jarubell, 15/12/2009 4 3372   05:59pm 16 Dec 2009
Question about servo motors Dupa, 15/12/2009 2 3615   12:46pm 15 Dec 2009
Capacitor vs Pulse Width Modulated MPPT bobshau, 09/12/2009 15 12299   05:41am 15 Dec 2009
Old Web Page Design Question MacGyver, 12/12/2009 5 3854   05:07am 14 Dec 2009
Thrust bearing failure imsmooth, 12/12/2009 7 3700   11:30pm 12 Dec 2009
Rotational Speed rmancini, 18/11/2009 11 4490   05:52pm 11 Dec 2009
Regrets. marcwolf, 11/12/2009 2 3020   11:11am 11 Dec 2009
New here Dupa, 09/12/2009 11 3367   12:48pm 10 Dec 2009
Tower Design Dupa, 10/12/2009 2 2909   12:33pm 10 Dec 2009
Predicting steel rotor size willib, 17/11/2009 2 2884   11:45am 10 Dec 2009
General Question About Frequency MacGyver, 06/12/2009 5 3772   12:21am 08 Dec 2009
Wood blades for small turbines Perry, 07/12/2009 4 3278   08:04am 07 Dec 2009
Newbie - why 3 blades? emdx, 30/11/2009 10 9793   11:25pm 06 Dec 2009
Check this Out Urban 108 KW JimBo911, 07/12/2009 2 3205   10:28pm 06 Dec 2009
chinese 300 watt electronic brake error rgormley, 06/12/2009 2 3408   03:16pm 06 Dec 2009
Informations on Ax flux generator ? Fusion, 01/12/2009 9 4484   07:26am 03 Dec 2009
Fiberglass blades MakeeK, 30/11/2009 1 3738   01:48am 01 Dec 2009
1X6C 7 phase delta KarlJ, 08/11/2009 28 11486   05:53am 27 Nov 2009
Where to buy Windmill Blades mark30504, 10/11/2009 2 3465   09:56am 26 Nov 2009
I finally got an F&P where to now? KarlJ, 14/10/2009 95 31211   10:23pm 25 Nov 2009
Safety first turnymf, 19/11/2009 4 3399   12:59am 25 Nov 2009
= New posts since you last visited .      

   Page 49 of 98    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026